Wireless Solution B-1000 Instrukcja Użytkownika Pobierz pdf (Strona 5)

BlackBox S-2

Transmitter

AC power input

(90-250VAC)

DC power input

(12VDC)

DMX universe 2 in (RJ45)

1: DMX- 5: n/c

2: DMX+ 6: n/c

3: n/c 7: Signal GND

4: n/c 8: n/c

DMX universe 1 in,

(XLR male 5pin)

Reserved

DMX universe 1 in (RJ45)

1: DMX- 5: +12VDC

2: DMX+ 6: n/c

3: n/c 7: Signal GND

4: +12VDC 8: DC GND

DMX universe 2 in,

(XLR male 5pin)

S-2

W-DMX

made in sweden

Universe 1 Universe 2

FUNCTION FUNCTION

Wireless Solution

Sweden AB

LINK LINK

DATA DATA

CTRL CTRL

W-DMX

made in sweden

Universe 1 Universe 2

FUNCTION FUNCTION

Wireless Solution

Sweden AB

LINK LINK

DATA DATA

CTRL CTRL

FUNCTION

Press and release

to search for and

link with receivers

(for each universe)

DATA (for each universe)

ON: Transmitting DMX data

CTRL (for each universe)

ON: Indicates that W-DMX bus link is active

LINK (for each universe)

ON: Normal operation

FLASH: Unlinking all receivers

RAPID FLASH: Linking with receivers

Installation

Please see left for installation details with the exception of step 2:

2 The S-2 unit can simultaneously transmit two separate DMX

universes. Link one or two DMX inputs to the two individual

DMX in sockets on the rear panel, as required.

To add receivers (Set up each universe separately.)

Note: You can add receivers at any time, even during operation.

1 For the ﬁrst DMX universe channel, power on only the receiver

units to be used with that universe - ensure that they are not

linked with any other transmitter (LINK indicators should be OFF).

2 On the transmitter unit, press and release the

FUNCTION button

for the appropriate universe channel. The channel will scan for all

unlinked receivers for a period of ten seconds - the LINK indica-

tor will ﬂash rapidly.

3 If successful, each receiver’s

LINK indicator will go ON. If any

failed, check that the receiver is in range and repeat procedure.

4 Now power on the (unlinked) receivers that will be linked with

the second DMX universe channel. Follow steps 2 and 3 for the

other universe channel to make it search for the receivers.

To unlink all receivers from a DMX universe channel

1 On the transmitter, press and hold the appropriate FUNCTION

button until LINK begins ﬂashing. All registered receivers linked

to that DMX universe channel will be unlinked.

DMX Interface

Transceivers on bus: 32 (max)

Data rate: 250 kbps (max)

ESD protection*: ±15 kV

AC input

90-250VAC 50/60Hz

1A at 115VAC (max)

0,5A at 230VAC (max)

DC input

12-24VDC 1,5A (max)

Compliance declarations

ETSI: EN300 328 & 300 826

EMC: EN301 489-17

CE: EN60950

FCC: UQT-WDXOEMPCBF

IC: 6812A-WDMXOEM

ARIB: 06215559/AA/00

RF characteristics

Output power:

20 25** dBm

100 300** mW

Frequency range:

2402 to 2479 MHz

Channel bandwidth: 1

Sensitivity at 0.1% BER:

-95dBm

* Slewrate limited for

minimum of EMI in unter-

minated networks.

** Only in FCC output

power mode.

Package Contents

In addition to this manual:

1 pc, BlackBox S-2

1 pc, Power cord

1 pc, DC connector

1 pc, Standard antenna

1 pc, Antenna adaptor

2 pc, Trussholder brackets

1 2 3 4 5 6 7 8 9 10 ... 19 20

Komentarze do niniejszej Instrukcji

Brak uwag

Wireless Solution B-1000 Instrukcja Użytkownika Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Odbiornik Wireless Solution B-1000