Wireless Solution R-512 Micro Lite Instrukcja Użytkownika Pobierz pdf (Strona 5)

w i r e l e s s

s o l u t i o n

Speciﬁcations

DMX interface

• Full compliance with USITT DMX-512 (1990) & 512-A standards

• Maximum number of transceivers on a single bus: 32

(compliant with the EIA/TIA RS-485 standard)

• Data Rate: 250 kbps (slew rate limited to minimise EMI)

• Electrostatic discharge protection: ±15kV

• DMX frame rate and frame size: Auto sensing

• Frame rate: 1 (min) to 44 (max) frames per second

• Frame size: 1 (min) to 512 (max) channels

• Loss of DMX input or radio link: After one second (if there is no

resumption), the DMX output will cease to transmit and go into

a high impedance mode.

• Recovery from loss of DMX input or radio link: Less than 1 second.

Power characteristics

• High voltage input: 90-260VAC

• Low voltage input: 12VDC (T-1 Pro and S-2: 12-24VDC)

• Average current (transmit mode): 450mA @ 12VDC

• Average current (T-1 receive mode): 200mA @12VDC

Battery operation (T-1 Pro only)

• 1 hour operation from fully charged in transmit mode

• 2 hours operation from fully charged in receive mode

RF characteristics

W-DMX

uses Adaptive Frequency Hopping Spread Spectrum

(AFHSS) and changes frequency every 910uS

• Operational frequency range: 2402-2479MHz (ISM band)

• EU/ASIA RF output power: 20dBm or 100mW

• FCC RF output power: 25dBm or 275mW

• Channel bandwidth: 1 MHz

• Sensitivity at 0.1% Packet Error Rate: 95dBm

• Tested link range 450m (Low power EU mode using standard

antennae in an urban area)

Approvals

•

FCC: 15.247&68 Class B; Canada ICES 003; Japan ARIB STD-T66

• CE;

EN 301 489-1; 301 489-17; EN 300-328-1; EN 300-328-2; EN 609 50

Enclosure

• Diecast aluminium casing

• Operating temp range: S-1 / S-2: 0

C to +55

C (32

F to 131

T-1 Pro: -20

C to +55

C (-4

F to 131

• Dimensions (W x H x D): 219 x 45 x 131mm (8.6” x 1.8” x 5.2”)

• Weight: 1005g / 35.45oz

Connectors

• N-type female antenna connector, N – RP-SMA adaptor included

• 2 Neutrik

XLR 5-pin gold plated DMX connectors

• 2 RJ45, DMX over Cat5 cable links

• 1 RJ45, W-DMX PC-link / Internal link (T-1 Pro only)

• 1 DC input, pluggable terminal strip, Phonix

MSTB 2,5

• 1 AC input, IEC-6C

Supplied accessories

• AC power cord / DC power connector / Standard antenna

Antenna adaptor / Mounting brackets / User guide

Part codes S-1 S-2 T-1 Pro

ETSI/FCC approved A40001 A40005 A40003

(power output:

100mW/300mW max.)

Japan ARIB approved A40001J A40005J A40003J

(power output:

100mW max.)

Phone: +46 522 511 511

Fax: +46 522 440 885

E-mail: [email protected]

Web: www.wirelessdmx.com

Wireless Solution Sweden AB

Stureparksvägen 7

451 55 Uddevalla

Sweden

AC power

input

(90-250VAC)

DC power

input

RJ-45 DMX

connector

XLR 5pin

DMX

connector

Reserved

RJ-45 DMX

connector +

DC power in

XLR 5pin

DMX

connector

Mode button (T-1 only)

Press to change between

transmitter and receiver.

Press to change between battery (T-1

only) (green indicator) and external

power input (red indicator) operation.

W-DMX bus port

(T-1 only) connec-

tion to another T-1

unit or to a PC.

Front and rear panel details

W-DMX

made in sweden

Level

Radio

Batt

Wireless Solution

Sweden AB

FUNCTION

POWERDATA

RXTX

CTRLLINK

T-1

pro

W-DMX

made in sweden

Level

Radio

Batt

Wireless Solution

Sweden AB

FUNCTION

POWERDATA

RXTX

CTRLLINK

RADIO

ON: Indicates that

Level display is show-

ing signal strength

BATT

ON: Indicates that

Level display is

showing battery

charge

FUNCTION

Operation depends

upon current

operation mode:

transmit or

receive.

Level Provides alternate indications

of radio signal strength and battery charge

every two seconds. The RADIO and BATT

indicators conﬁrm which function is currently

being shown.

DATA

ON: Transmitting/

receiving DMX data

TX/RX

Indicate current

operation mode

CTRL

ON: Indicates that W-DMX

bus link is active

POWER

OFF: Off or using battery

ON: External power input

FLASH: Charging battery

LINK

ON: Normal operation

FLASH: Unlinking all receivers

RAPID FLASH: Linking with receivers

OFF: Not linked to a transmitter

ON: Linked to a transmitter

RAPID FLASH: Linking to a transmitter

TX MODERX MODE

T-1 Pro

LINK

ON: Normal operation

FLASH: Unlinking all receivers

RAPID FLASH: Linking with receivers

W-DMX

made in sweden

Level

Radio

Batt

Wireless Solution

Sweden AB

FUNCTION

POWERDATA

RXTX

CTRLLINK

S-1

W-DMX

made in sweden

Level

Radio

Batt

Wireless Solution

Sweden AB

FUNCTION

POWERDATA

RXTX

CTRLLINK

RADIO

ON: Indicates that

Level display is

showing signal

strength

BATT Not used

FUNCTION

Press and release

to search for and

link with receivers

Level Provides indication

of radio output signal strength

DATA

ON: Transmitting DMX data

RX & CTRL Not used

POWER

ON: Correct power

input present

S-1

S-2

W-DMX

made in sweden

Universe 1 Universe 2

FUNCTION FUNCTION

Wireless Solution

Sweden AB

LINK LINK

DATA DATA

CTRL CTRL

W-DMX

made in sweden

Universe 1 Universe 2

FUNCTION FUNCTION

Wireless Solution

Sweden AB

LINK LINK

DATA DATA

CTRL CTRL

FUNCTION

Press and release

to search for and

link with receivers

(for each universe)

DATA (for each universe)

ON: Transmitting DMX data

CTRL (for each universe)

ON: Indicates that W-DMX bus link is active

LINK (for each universe)

ON: Normal operation

FLASH: Unlinking all receivers

RAPID FLASH: Linking with receivers

S-2

Antenna

connector

Release 1-0d (October 2007) Speciﬁcations subject to change without notice

1 2 3 4 5 6 7 8 9

Komentarze do niniejszej Instrukcji

Brak uwag

Wireless Solution R-512 Micro Lite Instrukcja Użytkownika Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Odbiornik Wireless Solution R-512 Micro Lite